 |
Форум iHDD.RU
Ремонт накопителей и восстановление информации
|
|
посоветуйте пожалуйста
|
| Автор |
Сообщение |
SAV
Зарегистрирован: 06.12.2007
Сообщения: 3
Откуда: Нижний Новгород
|
 Добавлено: Чт, 06 Дек, 2007 20:49 Заголовок сообщения: посоветуйте пожалуйста |
 |
|
всем привет!
заметил неадекватное поведение у свего компа, помогите пожалуйста с диагностикой.
Система с двумя винчестерами, оба Segate Barracuda. Один постарше(4 года) - на 40Гб, другой совсем молодой(6 месяцев) на 250Гб, детальную информацию о них прикрепляю ниже.
Симпотомы проблемы такие: при работе в Windows XP, после некоторого времени работы слышен "хрюк" винчестера, после которого система подвисает и не реагирует ни на что, кроме кнопки выключения 
при работе в Linux (kubuntu7.10) после "хрюка" в логах ядра вижу записи: seek error, DMA disabled и начинаются тормоза. Повторное включение DMA возвращает систему в работоспособное состояние.
Что это может быть?
Вот данные о первом винчестере:
| Код: | === START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda ATA IV family
Device Model: ST340016A
Serial Number: 3HS16RFS
Firmware Version: 3.10
User Capacity: 40 020 664 320 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Dec 6 20:35:33 2007 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 422) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 071 063 034 Pre-fail Always - 82872413
3 Spin_Up_Time 0x0003 084 070 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 462
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 87036329
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3375
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 020 Old_age Always - 2610
194 Temperature_Celsius 0x0022 030 047 000 Old_age Always - 30
195 Hardware_ECC_Recovered 0x001a 071 063 000 Old_age Always - 82872413
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 2
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 2
199 UDMA_CRC_Error_Count 0x003e 200 087 000 Old_age Always - 1106
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 835 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 835 occurred at disk power-on lifetime: 2969 hours (123 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 04:10:32.546 READ DMA
c8 00 08 00 00 00 e0 00 04:10:32.114 READ DMA
10 00 3f 00 00 00 e0 00 04:10:32.114 RECALIBRATE [OBS-4]
c8 00 08 00 00 00 e0 00 04:10:31.694 READ DMA
c8 00 08 00 00 00 e0 00 04:10:31.261 READ DMA
Error 834 occurred at disk power-on lifetime: 2969 hours (123 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 04:10:32.114 READ DMA
10 00 3f 00 00 00 e0 00 04:10:32.114 RECALIBRATE [OBS-4]
c8 00 08 00 00 00 e0 00 04:10:31.694 READ DMA
c8 00 08 00 00 00 e0 00 04:10:31.261 READ DMA
f8 00 00 00 00 00 e0 00 04:10:31.241 READ NATIVE MAX ADDRESS
Error 833 occurred at disk power-on lifetime: 2969 hours (123 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 04:10:31.694 READ DMA
c8 00 08 00 00 00 e0 00 04:10:31.261 READ DMA
f8 00 00 00 00 00 e0 00 04:10:31.241 READ NATIVE MAX ADDRESS
ec 00 01 00 00 00 a0 00 04:10:29.638 IDENTIFY DEVICE
c6 00 00 00 00 00 a0 00 04:10:29.638 SET MULTIPLE MODE
Error 832 occurred at disk power-on lifetime: 2969 hours (123 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 04:10:31.261 READ DMA
f8 00 00 00 00 00 e0 00 04:10:31.241 READ NATIVE MAX ADDRESS
ec 00 01 00 00 00 a0 00 04:10:29.638 IDENTIFY DEVICE
c6 00 00 00 00 00 a0 00 04:10:29.638 SET MULTIPLE MODE
10 00 3f 00 00 00 a0 00 04:10:29.638 RECALIBRATE [OBS-4]
Error 831 occurred at disk power-on lifetime: 2967 hours (123 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 00 02:25:16.761 READ DMA
c8 00 08 00 00 00 e0 00 02:25:16.344 READ DMA
10 00 3f 00 00 00 e0 00 02:25:16.344 RECALIBRATE [OBS-4]
c8 00 08 00 00 00 e0 00 02:25:15.923 READ DMA
c8 00 08 00 00 00 e0 00 02:25:15.485 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging |
а вот о втором:
| Код: | === START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.9 family
Device Model: ST3250824A
Serial Number: 4NF253D8
Firmware Version: 3.AAH
User Capacity: 250 059 350 016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Dec 6 20:36:20 2007 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 100) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 103 073 006 Pre-fail Always - 6093130
3 Spin_Up_Time 0x0003 085 085 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 264
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 071 060 030 Pre-fail Always - 13426710
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 401
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 326
187 Unknown_Attribute 0x0032 096 096 000 Old_age Always - 4
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 068 052 045 Old_age Always - 538902560
194 Temperature_Celsius 0x0022 032 048 000 Old_age Always - 32 (Lifetime Min/Max 0/17)
195 Hardware_ECC_Recovered 0x001a 072 048 000 Old_age Always - 224104527
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 34
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 22 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 22 occurred at disk power-on lifetime: 233 hours (9 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a6 88 00 f0 Error: UNC at LBA = 0x000088a6 = 34982
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 68 9f 88 00 f0 00 01:04:11.156 READ DMA EXT
25 00 70 97 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 78 8f 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 80 87 88 00 f0 00 01:04:11.152 READ DMA EXT
25 00 78 0f 88 00 f0 00 01:04:11.152 READ DMA EXT
Error 21 occurred at disk power-on lifetime: 233 hours (9 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a6 88 00 f0 Error: UNC at LBA = 0x000088a6 = 34982
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 70 97 88 00 f0 00 01:04:11.156 READ DMA EXT
25 00 78 8f 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 80 87 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 78 0f 88 00 f0 00 01:04:11.152 READ DMA EXT
25 00 08 07 88 00 f0 00 01:04:11.152 READ DMA EXT
Error 20 occurred at disk power-on lifetime: 233 hours (9 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a6 88 00 f0 Error: UNC at LBA = 0x000088a6 = 34982
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 78 8f 88 00 f0 00 01:04:11.156 READ DMA EXT
25 00 80 87 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 78 0f 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 08 07 88 00 f0 00 01:04:11.152 READ DMA EXT
25 00 80 87 87 00 f0 00 01:04:11.152 READ DMA EXT
Error 19 occurred at disk power-on lifetime: 233 hours (9 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 a6 88 00 f0 Error: UNC at LBA = 0x000088a6 = 34982
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 80 87 88 00 f0 00 01:04:11.156 READ DMA EXT
25 00 78 0f 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 08 07 88 00 f0 00 01:04:11.155 READ DMA EXT
25 00 80 87 87 00 f0 00 01:04:11.152 READ DMA EXT
25 00 78 0f 87 00 f0 00 01:04:11.152 READ DMA EXT
Error 18 occurred at disk power-on lifetime: 4 hours (0 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 c0 50 d5 f0 00 04:15:47.379 READ DMA EXT
25 00 01 c0 50 d5 f0 00 04:15:46.946 READ DMA EXT
10 00 3f 00 00 00 f0 00 04:10:26.282 RECALIBRATE [OBS-4]
25 00 01 c0 50 d5 f0 00 04:10:14.054 READ DMA EXT
25 00 01 c0 50 d5 f0 00 04:09:27.437 READ DMA EXT
SMART Self-test log structure revision number 1
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay |
|
|
| Вернуться к началу |
|
 |
Antech
Зарегистрирован: 03.10.2005
Сообщения: 568
|
| Добавлено: Пт, 07 Дек, 2007 10:11 Заголовок сообщения: |
|
|
SAV
На первом винте два нечитамых сектора (рекомендуется скан в MHDD с включенным ремапом) и много (1106) интерфейсных ошибок (рекомендуется заменить шлейф, проверить питание и снять разгон, если есть).
На втором винте - тоже интерфейсные ошибки (34). |
|
| Вернуться к началу |
|
|
SAV
Зарегистрирован: 06.12.2007
Сообщения: 3
Откуда: Нижний Новгород
|
| Добавлено: Пт, 07 Дек, 2007 10:21 Заголовок сообщения: |
|
|
Antech,
спасибо за ответ. Попробую изучить программу MHDD и заменить шлейф.
Могут ли интерфейсные ошибки быть спровоцированны "старой" материнкой, блоком питания?
о разгоне не слышал ранее - как узнать включен ли он? |
|
| Вернуться к началу |
|
|
Antech
Зарегистрирован: 03.10.2005
Сообщения: 568
|
| Добавлено: Пт, 07 Дек, 2007 13:29 Заголовок сообщения: |
|
|
SAV
Могут ли интерфейсные ошибки быть спровоцированны "старой" материнкой, блоком питания?
Да.
разгоне не слышал
Значит его нет  .
www.overclockers.ru |
|
| Вернуться к началу |
|
|
|
|
FAQ
Поиск
Пользователи
Группы
Регистрация
Профиль
Войти и проверить личные сообщения
Вход
Общий форум
